Our regular 700 Series – the heart of EP acceleration reducer products – has been serving industry reliably for over a decade. Its proven modular style has set the sector standard for performance and may be the most imitated merchandise in today’s worm gear velocity reducer marketplace. But why settle for a knock-off when you can have the initial – from EP.
11 basic single reduction sizes
8 basic dual reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow output shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in share)
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for much longer operating life.
Its multi-position mounting versatility permits installation in practically any position.
Housings are straddle-milled, top and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged housing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, and also greater precision during worm and gear alignment.
EP 700 Series high-strength bronze worm equipment is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill, level, and drain in almost any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal life.
Both 2D and 3D CAD drawings are available in our eCatalog.
EP worm gearboxes have earned a reputation to be a business benchmark worldwide. Our achievement originated from our relentless get for quality with state-of-the-artwork technology, all and will be offering worm gearboxes happen to be affordable prices. High flexibility accorded through a broad choice of mounting choices, shaft configurations and electric motor interfaces, produces the EP worm gearbox the default decision for the sector. The helical-worm and the double-worm version, with or without the torque limiter, soon add up to the advantage, creating a highly versatile drive system.
EP Worm gearboxes provide high torque with low swiftness gear ratio. Being basic and compact in design, these gears can perform higher gear ratio compared to the helical gears. These worm reduction gears having screw type qualities act like helical gears, but its helix angle is typically comparatively bigger) and its own body is normally quite long in the axial direction. The gears in these gearboxes could be correct or left-handed dependant on the purpose.
Mounting choice include universal housing, aspect flanges, foot (horizontal and vertical), shaft mounted with torque arm. Available in Solid shafts (one or dual), with torque arm or torque limiter.
Worm reduction gears features
A worm gear is a kind of interlocking gear composed of a worm shaft and worm wheel. The worm is definitely shaped like a screw and the worm wheel is definitely a type of gear machined to have a tooth profile with the same configuration.
The procedure of a worm gear is similar with that of a bolt and nut. The principle is equivalent to a nut that has been fixed so that it cannot rotate and for that reason progresses in the axial path when the bolt is usually turned.
The design of a worm gear is thought of through the relationship between the rack and spur gear on the center plane of the worm wheel.
Great reduction ratio One rotation of the worm rotates the worm wheel by one tooth. Because of this, in a 1 speed reduction gears, the wheel can be manufactured therefore that it will be rotated 1/60 (1/120 in particular applications).
Orthogonal shaft The shafts are aligned orthogonally due to the structure. This characteristic can help you layout the turning transmitting direction at the right angle.
The arbitrariness of the rotation direction The screw direction of the worm can be clockwise or counterclockwise (generally clockwise). It is possible to switch the rotation direction of the worm wheel by changing the screw path.
A multitude of shaft layouts The wide selection of shaft layouts is one of the features of interlocking gears.For instance, right shaft output, remaining shaft output, dual shaft input and dual shaft output, etc., combine for a total of 14 types (Physique 2) and, if attachment orientations are included, it is possible to select from over 40 layouts.
Low noise, low vibration The interlocking of the worm and worm wheel is usually characteristic since the contact is certainly linear and the relative slide is fantastic. In comparison to rolling power transmission, sound and vibration are extremely low. Because of this, this technology is used to drive medical devices, elevators and escalators, etc.
The primary specifications of worm reduction gears
Center distance(mm) 32,40
Reduction ratio 10,20,30,40,50,60
Input capacity(kW) 0.1～1(at an input of 1800 rpm)
Output torque(N・m) 20～66
Input speed(rpm) 0～1800
Center distance(mm) 50,63,80,100,125,140,160
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.4～30(at an input of 1800 rpm)
Output torque(N・m) 900～3570
Input speed(rpm) 0～1800
Center distance(mm) 50,60,70,80,100,120,135,155,175,200,225,250,300,350,400,450,500
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.3～255(at an input of 1800 rpm)
Output torque(N・m) 50～56600
Input speed(rpm) 0～1800
Key points when choosing a worm reduction gears
When selecting a worm reduction gears, the procedures for selecting the correct gear are described in the manufacturer catalogs and the series and models ought to be selected according to those procedures. Particular care should be taken in crucial areas such as selecting the strain index, calculating the overhang load and examining heat rated ability from the manufacturer.
Cautions during use
When utilizing a worm reduction gears, the heat produced through the initial amount of use is large and running-in operation at 1/4, 1/2 and 3/4 of rated torque for eight hour periods is key to sufficiently attaining the performance of the worm decrease gears.
Maintenance and inspection
After completing running-in operation (approximately 50 hours), it is necessary to improve the lubricating oil and to change the lubricating oil from then on about 1 time per year according to the operation manual offered by the manufacturer.
The Worm Reduction Gear Box is provided by our company is of supreme quality. Our products are made by using premium quality materials and advance technology at our vendors end. These are widely used in a variety of sectors. Our products are easily available at a very low market prices.
Motor Mount Frame Options
TEC Motors, worm decrease gearbox.
Option A-160 B5 Body, Flange Mount.
Choice B-132 B14 Frame, Face Mount.
Option C-100/112 B5 Frame, Flange Attach.
High efficiency and safe operation. High load capability and overload functions. Output Torque = (Electric power (kW) x 9550 (Regular))/ Gearbox result speed (rpm).
Higher ratios available on request dependent on service factor (40:1, 50:1, 60:1, 80:1, 100:1)
Wormgears of the VF series are milestones for the industry worldwide. They succeeded in merging uncompromising top quality with stateoftheart technology amd renown price effectiveness.Absolute versatility is distributed by the wide selection of several mounting options, shaft configurations and engine interface, all offered as regular. The helicalworm and the doubleworm version, with or without the torque limiter, also add up, creating a highly versatile drive system.
20 level C TO 80 level C
The worm reduction gears can be found in two series: X and H.
The series X, having a worm and worm wheel set, comes in versions XA with shaft and XF-XC with mounting provisions for motor.
Version XF (bell casing + coupling) provides great versatility to suit a broad range of applications and provides higher efficiency compared to the compact brand XC, where the emphasis is on space effectiveness.
Series H offers the same features since series X with an added plus: a spur equipment pre-stage at the insight end provides higher performance and a broader range of ratios compared to the X series.
Framework sizes 110 and 90 include a cast-iron casing cast enbloc, whereas smaller sizes make use of die-cast aluminium housings. The worm shaft is manufactured from casehardened and hardened alloy steel and ground-finished.
The worm wheel has a cast iron hub with cast bronze insert. Hollow output shaft comes as standard.
Broad range of options available:
second input, result flange, single or dual extension result shaft, torque limiter with through wire, torque arm.